-40%
10,000 WATT Battery Dump Controller SOLAR Wind Regulator G4 440 24 VOLT N
$ 31.67
- Description
- Size Guide
Description
Solar Controller Diversion load regulator Charge regulator Charge controller Battery regulator 12 volt 24 volt 48 VDC volt wind power charge controller renewable energy dump load diversion load440 AMP WIND / SOLAR
CONTROLLER G4 440 24 VDC - 24 Volt System
Fully programmable for any voltage range you like.
Buy 1000 Watt Dump load here
CLICK HERE TO SEE 24V DUMP LOAD
Programming G4 solar wind turbine dump diversion load regulator - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
#G5 - 36 and 48 Voltbattery controller for wind turbine and solar panels - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Programming G4 solar wind turbine dump diversion load regulator - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
SEA440AJE wind turbine charge controller battery regulator - YouTube
Video will open in a new window
Using the eBay App? Paste link into a browser window:
[isdntekvideo]
Max solar amperage in
dump mode
is 250 amps. This is a huge hybrid wind and solar charge controller.
Use for wind or solar or both at the same time up to 300 amps dump continuous! Also use for hydroelectric and solar combinations both. User changeable settings -- Several controllers on the market only let you set the dump level!
Max continuous solar amperage in
disconnect mode
is 100 amps but it can take 440 amps surges from wind gusts no longer than 15 seconds each every 3 to 4 minutes max.
Can divert the charging source from the batteries to the load, or dump both the batteries along with the charging source.
You can connect both wind and solar at the same time
Reverse polarity protection
Ultra low power consumption even with the volt meter on (almost negligible). You can even set the volt meter to turn off after in-activity.
On board relay- Isolates electronics from back voltage spikes.
This is important to get the longest life out of the electronics. No body else has this!
Dual (2) Microprocessor controlled -- Extremely stable and very accurate
Multiple user changeable settings, and trip points for many various system requirements and applications- You can change the dump point voltage level,
end of dump voltage level, length of time in divert mode when end dump point voltage is reached (between 0 to 999 seconds, or 0 to 999 minutes)
Isolated Electronics Protection - Impossible to accidentally connect wind or solar directly to the circuit board.
High amp rating - 440 amps, 10,000 watts surge peak max. Wind in dump mode.
Battery Status digital LED - Lets you know your battery's actual voltage in real time!
Green LED come on and then you know it's in dump mode or cut mode depending on how your relay lugs wired.
Plug and Play - Long leads for easy termination to your 12 volt battery or battery bank.
WIND/SOLAR 24 VOLT DUMP / DISCONNECT CHARGE CONTROLLER
WITH BUILT IN DIGITAL DISPLAY AND INTELLIGENT DUAL PROCESSOR CONTROLLER
For solar panels and solar
LOWEST COST 440 AMP CHARGE OR DIVERT CONTROLLER WITH DIGITAL DISPLAY ON THE MARKET
20 YEAR WARRANTY
IT CAN DISCONNECT THE INCOMING POWER
OR DIVERT IT
TO A DUMP LOAD.
Battery regulator for both your wind and solar battery input power. This
regulator can either dump extra power creating free hot water or heat or
just cut off extra power to keep your batteries from over charging. This
unit is a must for wind turbine applications as it uses a mechanical
relay which can handle high voltage surges unlike solid state controllers.
10,000 WATT Rated (Tested to 467 Amps at low voltage)
15 years of great products
This controller can CUT-OFF incoming power so NO DUMP LOAD resistor is needed if you do not want to buy one - SAVE LOTS of MONEY not needing to buy a dump!
(Cut load works for 12 and 24 volt systems only. For 48 volt systems dump loads are highly recommended and cut load is a bad idea due to excessive relay arcing at high voltage levels during extreme windstorms.)
This item is the only controller that will work with wind turbines Do not buy solid state solar controllers as they will burn out in high wind conditions. This controller was specially developed for wind turbines after 35 years of research. Also works on solar too as a
battery controller
- Get one battery controller to do it all! if you can keep the battery from overcharging doesn't matter how the energy gets to that battery, solar, wind or Hydro-power. The idea is to make the battery the entire center of all voltage control.
Worlds Lowest Cost 440 AMP
Wind & Solar Controller
Battery Regulator-
Cut/Disconnect Controller-
Diversion Load Regulation-
This controller can divert or simply disconnect
incoming power without an electrical arc occurring -
HOW POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses almost no power when it is NOT dumping (energy efficient sensing)
In DISCONNECT mode it draws .2 amps but that's good since that means you have too much power in your batteries anyhow.
This High Amp unit can control 12 wind turbines or 40 solar panels !
Used to prevent battery over charging on
Wind - Solar - Hydro
A battery regulator diverts excess power to power
some other useful device when ever your battery is full.
Use the this excess power to make free hot water or to recharge an auxiliary battery bank, so many uses!
Has push button load tester.
An extremely robust unit!
draws almost ZERO power while sensing! 99.9% electrically efficient while sensing!
This controller may look fiendishly simple but it took 16 years of labor and custom parts testing in order to make it long
lasting and dependable. Built to take over 500 Million cycles or about 85 years of switching for the average system. TESTED for 16 years and proven 100% durable!
Versatile! Regulates all sectional battery banks
Requires only 24 volts to give a representative reading of
your whole battery bank no matter how large it is!
Battery regulator.
Charge regulator.
Charge controller.
Dump load regulator.
"Cut" charge controller.
Diversion load regulator.
Micro processor controlled.
Versatile raised steel mounting plate.
Measures 10" long by 4" wide by 3" tall.
Works for all Wind Turbines, Solar panels and Hydro.
For all voltages ranges in multiple battery banks.
No grounded IGBT's or MOSFETS - Lighting strike proof isolation.
CUT -LOAD
controller (No need to buy a dump load resistor)
Electrically efficient. Draws only trace power while
sensing
!
Does not waste electricity while
sensing
in diversion load mode!
HOW POWER DRAW DYNAMICS WORKS:
If you use it as a DIVERSION or DUMP load MODE then it uses no power
when it is NOT dumping (energy
efficient
sensing) In DISCONNECT mode.
The modern way to monitor your battery from over charging is to have a diversion load that performs another task such as heating water when your battery is in danger of over charging. Shutting down the output of your wind turbine or your other renewable energy devices is old school thinking. Now-a-days most people dump their excess power into some other legitimate device optimizing their energy independence. Hot water from your excess power can be used for radiant heating in the winter or even in the hot summer months for washing cloths or dishes and for bathing. You will always find a need for hot water in your life.
CUT MODE OPERATION
>