12x 67" Wind Turbine Generator Blades + Hub + Nose Cone 12 socket fit 17mm Shaft

Description

Nose Cone + Hub + 12 x 29" Nylon 6.6 Wind Turbine Generator Blades
For 17mm Shaft Mo
tors
(Wind turbine not included)
Brand new~
Environment friendly~
Features:
- Reduce wind resistance
- Eliminates vortexes
- Greater stability
- Increase swept area with 10"diameter
- Precisely machined, wobble-free
- Direct fit to 17mm PMA / Motors
- Excellent for PMA's Permanent Magnet Alternators
- Replace / Upgrade your Hub and nose cone
What are included:
- 1x Nose Cone
- 1x Hub
- 12x Wind Turbine Blades
Installation:
Installed on PMA with 17mm shaft
PMA Motor NOT INCLUDED
Hub Specifications:
Material
Aluminum (with coating)
Diameter
258 - 270 mm
Capacity
2 - 12 Blades
Compatibility
Fit 17mm Motor
Shaft Diameter
17mm shaft
Disc Thickness
26mm
Nose Cone
Specifications:
Material
Plastic
Inner Diameter
258mm
Height
93mm
Mounting
Snap On
Thickness
3mm
Performance Comparison:
With Nose Cone - Smooth Performance
Without Nose Cone - Air current spins into tiny vortexes
Nylon Blade Specifications:
Material
Nylon 6.6 + Carbon Fiber (<20%)
Length
29 inches
Width (base)
6 inches
Compatibility
Car alternators, AMETEK, tape drive, stepping, 90 VDC motors
Mounting
6mm bolts
Weight (per blade)
300g, 0.66lbs
Accessories:
-12 Degree Adjusters
-
24
M6x25 Stainless Steel bolts
- 24 hex Nylocks nuts (auto locks thread)
What is Nylon 6.6?
Nylon is a man made product. On the man made side, you will see primarily three types of thermoplastic. These are polyester, polypropylene, and nylon. Of the three types, nylon is by far the better choice.
Nylon is extremely versatile in its applications. It is highly resistant to
abrasion
and has excellent
resilience
.
Within nylon, there are two groups:
nylon 6
and
nylon 6.6
. Nylon 6.6 is the
premium thermoplastic
. It is the thermoplastic that is most often specified by professional architects and designers because it provides the
flexural strength
,
low-temperature toughness
and is the most
resilient
. Nylon 6.6 performs well in many applications such as wind turbine blades, automotive parts, and other fields that get a lot of wear and tear. Nylon 6.6 has additional molecules that give extra strength and the resilience compared to nylon 6. If you still have no idea what Nylon 6.6 is, do a search on google.
Features:
- 29" inches long, longest in the market
- With 67" swept area when mounted on a 10" rotor
- Incorporates highly efficient, true airfoil
- Quiet performance with minimal vibration
- Super slim, spins up to 1500RPM
- Can generate 800 watts or more depending on your PMA efficiency
- Manufactured using a precision injection molding process that produces blades of exceptional consistency
- Made with new thermoplastic to increase durability
- Smoother and more durable than any blades you can find in the market
- Adjustable blade degree with included degree adjuster (see picture)
- 17mm hub centers fits on most car alternators, AMETEK, tape drive, stepping, 90VDC motors
- Slight metal work required for 5/8" shafts
- Excellent for PMA's Permanent Magnet Alternators
- 7 inches longer and 1.5 inches wider than factory blades
- Replace / Upgrade your wind turbine blades
- High resistance to bending (over 150 degrees)
Adjustable blade degree with included degree adjuster
Increase/decrease blade angle by installing degree adjuster under the blades
"+" on the right side = Increase angle =
More
Torque, Less Speed
"-" on the right side = Decrease angle = Less Torque,
More
Speed
Please note this enhancement is only available from us. The so-called "defect" our competitor has claim is completely false and proves his ignorance in mechanical engineering.
Below are comparisons between the our improved blade, competitor's blade and the original Air X blade. It has been divided into 4 categories: Surface, Angle, Base and Tip
Blade Surface:
Our Blades
Competitor's
Air-X
Pros:
- Made from
100%
new raw material
- 80% Nylon 6.6 thermoplastic
- 20% carbon fibre
- Only new materials will give the
shine
above
- Extremely flexible
- Low temperature toughness
- UV Resistance
Cons:
- Made from
brittle, recycled
plastic
- Fragments and debris can be found at the edge of the blade circled above - sign of recycled material
- Fragments will tear wind and create undesirable vortex behind the blades
- No shine at all
- The dull and dusty look are signs of
High fibre concentration
- High fibre will
prevent shrinking
, however, it makes the blade very
brittle
because plastics do not stick to fibres well, it will introduces
cracks
that will allow water to absorbed in. Due to the fact that water will
expand
when it freezes to ice,
two things
can happen:
In the less severe case, the surface of the blade will start to "
peel off
" like burnt skins
In the worst case, when there is enough peeling or a large enough crack, the blade will
snap
- Cracks can be found at the base of the blades
Pros:
- Made of new material, however it is not as shiny because of the
flow lines
*
*Directionally "off tone" wavy lines or patterns
Blade Angle:
Our Blades
Pros:
- To compensate the bending force from the wind, blades are slightly angled towards the direction of wind.
Competitor's
Cons:
- Poor Design, blades are angled away from wind. They might start hitting pole in strong wind
Air-X
Pros:
- To compensate the bending force from the wind, blades are slightly angled towards the direction of wind.
Base:
1. Mounting Base
Our Blades
Competitor's
Air-X
Pros:
- Mounting Base has been machined to make sure it will fit the hub perfectly
Cons:
- Mounting Base has not been machined so it is not flat
-
2mm
shrink / sink mark:
- Different angle for different blade will causes vibration
Pros:
- Mounting Base has been machined to make sure it will fit the hub perfectly
2. Mold
Our Blades
Competitor's
Air-X
Pros:
- The depth of our injection mold is
2.5"
-
Allows the shape of the bolt to be integrated into the blade
(
see dotted lines and picture below
)
- The mold is much
more expensive
than the thin ones our competitor's use
- Produce quality blades that will not shrink
Cons:
- Depth of the injection mold is approximately
1.25"
- Mounting base has to be
tilted at an angle
to compensate the lack of space
- Holes for bolts are
not integrated
due to restrictions set on the mold (ie: Mounting base is a
parallelogram
instead of rectangular)
- Holes are drilled after blade is produced and maybe
off centered
- Mold is much
cheaper
because it is thin
- Mold has an inferior design that compromise performance
Pros:
- Depth of the injection mold is approximately
1.5"
- Does not need to be thick because their blades is 22"
-
Allows the shape of the bolt to be integrated into the blade
(
see dotted lines and picture below
)
3. Edges
Our Blades
Competitor's
Air-X
Pros:
- Edges of the blade is smooth, no
Flash*
at all
*The terms "flash", "fins", and "spew" are used to refer to excess molding material that penetrates into mold gaps (i.e., between parting faces, slide push-out faces, and inserts, etc.) in a molten state.
Cons:
- Due to the lack of thickness / strength in the mold there is not enough clamping force to hold the two mold pieces together during injection
- Result is:
a 3mm
HUGE
Flash
- Totally compromise performance because blade is
deformed
Pros:
- Minor flashes can be found but they do not affect performance
4. Injection Point
Our Blades
Competitor's
Air-X
Pros:
-
3mm
Injection point
- Prevents Shrink marks
Cons:
- Approximately
2.5mm x 15mm
Injection point
- Mold is
damaged
and created Blister
- A bad place to be chose for injection (right on the edge of the blade)
- Performance is
compromise performance
due to wind drag
Pros:
-
4mm
Injection point
- Prevents Shrink marks
Blade Tip:
Our Blades
Competitor's
Air-X
Pros:
- Smooth, rounded blade tip to minimize wind drag
Cons:
- Flash has to be cut off from blade tip due to poor mold design
- Tip will tear incoming wind and create drag
Pros:
- Smooth, rounded blade tip to minimize wind drag
WARNING !!!
SHARP Edges, Handle with Care!
Rotating blades present the most serious mechanical hazard. The blades may be moving at velocities over 275 miles per hour (440 km/hr). At this speed, the tip of a blade is nearly invisible and can cause serious injury. Under no circumstances should you install the turbine where a
person could come in contact with moving rotor blades.
The installer of these blades is solely responsible for the use or misuse of these blades. We assume no liability for ANY injuries caused by these products.
NO OPERATING COST
GENERATES ELECTRICITY FROM THE ABUNDANT RESOURCE - WIND
Terms & Conditions
Bidding this auction means that you agree with the following terms & conditions.
All pictures and descriptions are subjected to change without notice. Items may not look exactly the same as the auction shown. We are not responsible for any inadvertent errors.
Payment
Total payment = winning price + shipping & handling
Insufficient payment will be charge extra US{{detail_product_description}}.50 to compensate the Paypal penalty fees.
Shipping
&
Handling
Total shipping = Base S&H + Combine S&H ( for each additional item )
a) Base S&H is the highest shipping cost of the first item.
1. Combine shipments are only available on the condition of a
SINGLE PAYMENT
. Auctions that are paid separately will NOT be shipped in combo and therefore, they are not qualified for shipping discounts.
2. We ship within 2 working days after payment is received and confirmed. Please allow up to
5-10 BUSINESS DAYS
for item(s) with a physical address sending to the 48 states of United States & Canada. For international bidders, the shipping time varies with respect to your location.
3. Bounce backs due to incorrect shipping address will result in setback on deliveries. It is the buyer's responsibility to repay the shipping & handling fees.
4. We are not responsible for any loses or damages resulting from shipping.
Return & Refund Policy
No refunds after 30 days
Shipping & handling & other service fees are
NOT
refundable
All returned items must be in original packing.
Items that are used/ damaged/ deformed or altered in any ways will not be accepted.
A 20% restocking fee will be charged on all refunded items.
E-mails
E-mails are usually answered within 2~3 business days in priority order.
Spams and mass e-mailing will be deleted without slightest glance.
E-mails with virus or anything subjected to hacking are automatically deleted.